Mossberg 930 Tactical Forend And Heat Shield

Tac Out Your Mossberg 930 With The 22 Plus GG&G American Made 930 Tactical Accessories HERE!

Mossberg 930 Tactical Forend And Heat Shield

The Work Horse Mossberg 930 was introduced in 2005. It is estimated that there are about 750,000 Mossberg 930's still operational. With the ability to use Additive Manufacturing (3D Printing), the GG&G New Product Development Team, thought it would be great to update the Tactical Presence of the Mossberg 930 Shotgun with a Replacement Tactical Forearm With M-LOK Slots, and while we were at it, design and develop an Integrated Tactical Heat Shield as an option. GG&G is offering the Mossberg 930 Integrated Heat Shield as an option because not all shooters use the "Extended Grip" technique and would prefer not to have one. But, even if you don't use the "Extended Grip" there are other reasons to use the 930 Heat Shield. One of them being "It Looks Bad Ass Tactical".

The New Tactical Mossberg 930 Forearm is full length and has a large dynamic textured surface area to aide in your grip. Especially useful  in stress situations. The M-LOK Slots at 3, 6, and 9 o'clock at the front of the Tactical Forend allow you to easily add M-LOK Sling Attachments, Light Rails and other M-LOK Accessories as needed. The Mossberg Tactical Handguard takes about five minutes to install just like the factory Mossberg forend. No installation hardware or special tools are required  Check out the specifications below.

The New Mossberg 930 Heat Shield is a full length one piece Heat Shield designed to easily mate with the GG&G Mossberg 930 Tactical Forend. The Replacement Forend or Mossberg barrel does not need to be removed for the 930 Heat Shield to be installed. The Heat Shield extends all the way back to the receiver and completely covers the top surface of the barrel. The 930 Heat Shield provides significant heat dissipation created during high round count shooting. Although vented, there are no vent holes at the critical "extended grip"  location to prevent major discomfort from the barrel heat or worse yet, burnt fingers. The ergonomics of the GG&G 930 Heat Shield accommodates shooters that like to roll the shotgun over, place the stock on their shoulder for support, and reload from this position.  Please note that the Mossberg Integrated Heat Shield cannot be installed without the New Mossberg 930 Tactical Forend being in place.
 

Mossberg 930 Tactical Forend Specifications:

• CALIFORNIA RESIDENTS:

  PLEASE NOTE THAT AS OF 1/1/2026, DUE TO CALIFORNIA’S NEW LEGISLATION REGARDING SEMI-AUTOMATIC SHOTGUN ACCESSORIES, A GG&G FOREND CANNOT BE SOLD OR SHIPPED TO CALIFORNIA.

• Installation takes approximately five minutes to install and does not require any modifications to your shotgun. 
• The 3D Printed Replacement 930 Tactical Forend is a full length one piece forend smoothly contoured to match the contours of the barrel and front of the receiver.
• The surface is dynamically textured in a pattern to aide in your grip.
• Three M-LOK Slots are located at the front of the Mossberg 930 Tactical Forend at 3, 6, and 9 o'clock for mounting M-LOK slings and light accessories.  
• GG&G manufactures several M-LOK Accessories that will fit the 930 Forend and meet your mission requirements. Check them out HERE.
• Two Small Filler Side Plates and two attachment screws are included to be used if the Mossberg 930 Heat Shield is not installed. These Filler Side Plates are installed to blend in the two 930 Heat Shield attachment points on the NewTactical Forend.
• Materials: Additive Manufactured from glass filled nylon polymer 
• Weight: 7.6 oz.
• Length: 11.125"
• Warranty: Lifetime.
• Made In America By Men And Women Proud To Be Americans!

Mossberg 930 Heat Shield Specifications:

• CALIFORNIA RESIDENTS:

  PLEASE NOTE THAT AS OF 1/1/2026, DUE TO CALIFORNIA’S NEW LEGISLATION REGARDING SEMI-AUTOMATIC SHOTGUN ACCESSORIES, WHICH CONCLUDES THAT A HEAT SHIELD (SHROUD) TRANSFORMS A SEMI-AUTOMATIC SHOTGUN INTO AN ASSAULT WEAPON, A GG&G HEAT SHIELD (SHROUD) CANNOT BE SOLD OR SHIPPED TO CALIFORNIA. 

• Installation takes approximately five minutes to install and does not require any modifications to your shotgun. 
• The 1/16" hex wrench supplied with the 930 Tactical Forend is the only tool required for installation. Follow the provided installation instructions.
• The 930 Heat Shield is designed and manufactured to integrate at four points with the Mossberg 930 Tactical Forend. Yep, it does not mount and will not function without the 930 Tactical Forend.
• Easily removed without removal of the Mossberg 930 Tactical Forend.
• The ventilated design offers protection from the hot barrel, especially after rapid shooting.
• Dynamic textured finger and hand grip at forward area aide in the "extended grip" off hand shooting style.
• Minimal barrel interface to reduce heat transfer to the shield.
• Four locking points of contact for a tight, rattle- free fit.
• Materials: Additive Manufactured from glass filled nylon polymer.
• Weight: 2.85 oz.
• Length: 10.9"
• Warranty: Lifetime.
• Made In America By Men And Women Proud To Be Americans!